document number: 85197 www.vishay.com revision: 1.0, 28-jan-10 1 ir receiver modules for remote control systems tsop852..ap5, tsop854..ap5 vishay semiconductors features ? very low supply current ? photo detectors and preamplifier in one package ? internal filter for pcm frequency ? supply voltage: 2.5 v to 5.5 v ? improved immunity against ambient light ? compliant to rohs directive 2002/95/ec and in accordance to weee 2002/96/ec ? insensitive to supply voltage ripple and noise ? halogen-free according to iec 61249-2-21 definition description the tsop852..ap5, tsop854..ap5 series are miniaturized receiver modules for infrared remote control systems. a pin diode and a preamplifier are assembled on a pcb, the epoxy lens cap is designed as an ir filter. the demodulated output signal can be directly decoded by a microprocessor. the tsop852..ap5 is compatible with all common ir remote control data formats. the tsop854..ap5 is optimized to suppress almost all spurious pulses from energy saving fl uorescent lamps but will also suppress some data signals. this component has not been qualified according to automotive specifications. block diagram application circuit 21944 parts table carrier frequency standard applications (a gc2/agc8) very noisy environments (agc4) 30 khz TSOP85230AP5 tsop85430ap5 33 khz tsop85233ap5 tsop85433ap5 36 khz tsop85236ap5 tsop85436ap5 38 khz tsop85238ap5 tsop85438ap5 40 khz tsop85240ap5 tsop85440ap5 56 khz tsop85256ap5 tsop85456ap5 30 k v s out demo- gnd pass agc input pin band dulator control circuit 4 3 1, 2 20445-3 c 1 ir receiver gnd circuit c r 1 + v s gnd transmitter with tsalxxxx v s v o 17170_5 out r 1 and c 1 are recommended for protection against eos. components should be in the range of 33 < r 1 < 1 k , c 1 > 0.1 f.
www.vishay.com document number: 85197 2 revision: 1.0, 28-jan-10 tsop852..ap5, tsop854..ap5 vishay semiconductors ir receiver modu les for remote control systems note (1) stresses beyond those listed und er absolute maximum ratings may cause permanent damage to the device. this is a stress rating only and functional operation of the device at these or any other cond itions beyond those indicated in the operational sections of t his specification is not implied. exposure to absolute ma ximum rating conditions for extended pe riods may affect the device reliability. note (1) t amb = 25 c, unless otherwise specified typical characteristics t amb = 25 c, unless otherwise specified fig. 1 - output function fi g. 2 - output pulse diagram absolute maximum ratings (1) parameter test conditi on symbol value unit supply voltage (pin 4) v s - 0.3 to + 6 v supply current (pin 4) i s 3ma output voltage (pin 3) v o - 0.3 to (v s + 0.3) v output current (pin 3) i o 5ma junction temperature t j 100 c storage temperature range t stg - 25 to + 85 c operating temperature range t amb - 25 to + 85 c power consumption t amb 85 c p tot 10 mw electrical and optical characteristics (1) parameter test condition symbol min. typ. max. unit supply voltage v s 2.5 5.5 v supply current (pin 4) v s = 3.3 v, e v = 0 i sd 0.27 0.35 0.45 ma e v = 40 klx, sunlight i sh 0.45 ma transmission distance e v = 0, ir diode tsal6200, i f = 250 ma, test signal see fig. 1 d35m output voltage low (pin 3) i osl = 0.5 ma, e e = 0.7 mw/m 2 , test signal see fig. 1 v osl 100 mv minimum irradiance pulse width tolerance: t pi - 5/f o < t po < t pi + 6/f o , test signal see fig. 1 e e min. 0.15 0.35 mw/m 2 maximum irradiance t pi - 5/f o < t po < t pi + 6/f o , test signal see fig. 1 e e max. 30 w/m 2 directivity angle of half transmission distance ? 1/2 75 deg e e t v o v oh v ol t 600 s 600 s t = 60 ms t on t off 94 8134 optical test signal output signal , (see fig. 4) 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.1 1 10 100 1000 10 000 e e - irradiance (mw/m 2 ) t on , t off - output pulse width (ms) 20759 = 950 nm, optical test signal, fig. 3 t on t off
document number: 85197 www.vishay.com revision: 1.0, 28-jan-10 3 tsop852..ap5, tsop854..ap5 ir receiver modules for remote control systems vishay semiconductors fig. 3 - frequency dependance of responsivity fig. 4 - sensitivity in bright ambient fig. 5 - sensitivity vs. supply voltage disturbances fig. 6 - sensitivity vs. electric field disturbances fig. 7 - max. envelope duty cycle vs. burst length fig. 8 - sensitivity vs. ambient temperature 0.0 0.2 0.4 0.6 0.8 1.0 1.2 0.7 0.9 1.1 1.3 f/f 0 - relative frequency 16925 f = f 0 5 % f(3 db) = f 0 /10 e /e - rel. responsivity e min. e 0 0.5 1 1.5 2 2.5 3 3.5 4 0.01 0.1 1 10 100 e e - ambient dc irradiance (w/m 2 ) e e min. - threshold irradiance (mw/m 2 ) correlation with ambient light sources: 10 w/m 2 = 1.4 klx (std. illum. a, t = 2855 k) 10 w/m 2 = 8.2 klx (daylight, t = 5900 k) wavelength of ambient illumination: = 950 nm 20757 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1 10 100 1000 vs rms - ac voltage on dc supply voltage (mv) 20753 e e min. - threshold irradiance (mw/m 2 ) f = f o f = 20 khz f = 30 khz f = 100 hz f = 10 khz 0 50 100 150 200 250 300 350 400 450 500 0 500 1000 1500 2000 2500 3000 f - emi frequency (mhz) e - max. field strength (v/m) 20747 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 020406080100120 burst length (number of cycles/burst) max. envelope duty cycle f = 38 khz, e e = 2 mw/m 2 tsop852.. tsop854.. 20817 0 0.05 0.1 0.15 0.2 0.25 0.3 - 30 - 10 10 30 50 70 90 t amb - ambient temperature (c) e e min. - threshold irradiance (mw/m 2 ) 20755
www.vishay.com document number: 85197 4 revision: 1.0, 28-jan-10 tsop852..ap5, tsop854..ap5 vishay semiconductors ir receiver modu les for remote control systems fig. 9 - relative spectral sensitivity vs. wavelength fig. 10 - directivity fig. 11 - sensitivity vs. supply voltage 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 700 750 800 850 900 950 1000 1050 1100 - wavelength (nm) s( ) rel - relative spectral sensitivity 21946 0.1 0.3 0.5 0.7 0.9 80 70 60 50 40 30 20 10 0 - 10 - 20 - 30 - 40 - 50 - 60 - 70 - 80 21947 0 0.02 0.04 0.06 0.08 0.1 0.12 0.14 0.16 0.18 0.2 23456 v s - supply voltage (v) e e min. - sensitivity (mw/m 2 ) 20756 3.5 4.5 5.5 2.5
document number: 85197 www.vishay.com revision: 1.0, 28-jan-10 5 tsop852..ap5, tsop854..ap5 ir receiver modules for remote control systems vishay semiconductors suitable data format the tsop852..ap5, tsop854..ap5 series is designed to suppress spurious output pulses due to noise or disturbance signals. data and disturbance signals can be distinguished by the devices according to carrier frequency, burst length and envelope duty cycle. the data signal should be close to the band-pass center frequency (e.g. 38 khz) and fulfill the conditions in the table below. when a data signal is applied to the tsop852..ap5, tsop854..ap5 in the presence of a disturbance signal, the sensitivity of the receiver is reduced to insure that no spurious pulses are present at the output. some examples of disturbance signals which are suppressed are: ? dc light (e.g. from tungsten bulb or sunlight) ? continuous signals at any frequency ? strongly or weakly modula ted noise from fluorescent lamps with electronic ballasts (see figure 12 or figure 13) fig. 12 - ir signal from fluorescent lamp with low modulation fig. 13 - ir signal from fluorescent lamp with high modulation note for data formats with sh ort bursts please see th e datasheet for tsop853.. 0101520 time (ms) 16920 ir signal ir signal from fluorescent lamp with low modulation 5 0101520 time (ms) 16921 ir signal ir signal from fluorescent lamp with high modulation 5 tsop852..ap5 tsop854..ap5 minimum burst length 10 cy cles/burst 10 cycles/burst after each burst of length a minimum gap time is required of 10 to 70 cycles 10 cycles 10 to 35 cycles 10 cycles for bursts greater than a minimum gap time in the data stream is needed of 70 cycles > 4 x burst length 35 cycles > 10 x burst length maximum number of continuous short bursts/second 1800 1500 recommended for nec code yes yes recommended for rc5/rc6 code yes yes recommended for sony code yes no recommended for thom son 56 khz code yes yes recommended for mitsubis hi code (38 khz, preburst 8 ms, 16 bit) yes no recommended for sharp code yes yes suppression of interference from fluorescent lamps most common disturbance signals are suppressed even extreme disturbance signals are suppressed
www.vishay.com document number: 85197 6 revision: 1.0, 28-jan-10 tsop852..ap5, tsop854..ap5 vishay semiconductors ir receiver modu les for remote control systems package dimensions in millimeters 1: gnd 2: gnd 3: v out 4: v cc 14 23 1 4 2 3 center of sens. area 4.5 1.3 (0.66) (0.85) (0.85) (10) view padside of device marking area proposed pad layout from component side (dim. for reference only) (3) (2.5) (1.15) (1.5) not indicated tolerances 0.2 specifications according to din technical drawings drawing-no.: 6.541-5081.01-4 issue: 2; 24.11.09 21916 (3.3) 5 pin 1 identification (marking picture for examply only)
document number: 85197 www.vishay.com revision: 1.0, 28-jan-10 7 tsop852..ap5, tsop854..ap5 ir receiver modules for remote control systems vishay semiconductors taping version tsop85...ap5tt dimensions in millimeters issue: 2, 24.11.09 21945 drawing-no.: 9.700-5346.01-4 for device orientation only optical center z 5:1 14 23 5.3 0.3 1.65 4.8 2 8 4 12 5.5 1.75 ? 1.5 min. z ? 1.55 direction of feed specifications according to din technical drawings
document number: 91000 www.vishay.com revision: 18-jul-08 1 disclaimer legal disclaimer notice vishay all product specifications and data are subject to change without notice. vishay intertechnology, inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, ?vishay?), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. vishay disclaims any and all li ability arising out of the use or application of any product describ ed herein or of any information provided herein to the maximum extent permit ted by law. the product specifications do not expand or otherwise modify vishay?s terms and conditions of purcha se, including but not limited to the warranty expressed therein, which apply to these products. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of vishay. the products shown herein are not designed for use in medi cal, life-saving, or life-sustaining applications unless otherwise expressly indicated. customers using or selling vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify vishay for any damages arising or resulting from such use or sale. please contact authorized vishay personnel to obtain written terms and conditions regarding products designed for such applications. product names and markings noted herein may be trademarks of their respective owners.
|
